observed IP ranges seen in the networking settings.
Hi Folks,I am not really a VMware guys but more into networking. We keep getting these queries from the VMware folks about the observed IP ranges in the network showing wrong entries. example if the...
View ArticleRe: vCenter Inventory Services
The user that I used is admin@system-domain. In the vsphere web client I use the admin@system-domain, and I can connect but I cannot see any Vcenter server, everything is "0". But in the tasks tab I...
View ArticleRe: vCenter Chargeback default superuser credentials
i same like you, in progress installing chargeback dont have user credential, but after installing and open application chargeback must put license key and super user credential. i find super user on...
View ArticleRe: vCloud Director - vShield Manager Registration
Please make sure that you entered the exact same value for the hostname of vCenter into vCloud Director and vShield Manager. If you put an IP into vShield and a Hostname into vCloud, this will fail to...
View ArticleRe: Гипервизор vSphere 5.1 не передает значения аппаратных датчиков на HP...
Обновил хост до билда 1065491 (это 5.1 U1a) и датчики появились.До этого был билд как у вас 799733 - видимо это глюк конкретной сборки.Обновитесь.
View ArticleRe: ESXi 4.0 Server Crashed
no i dont have an active contract # fdisk -lu Disk /dev/disks/eui.00e09e0000fe0f5f: 72.8 GB, 72839168000 bytes64 heads, 32 sectors/track, 69464 cylinders, total 142264000 sectorsUnits = sectors of 1...
View ArticleRe: HA Configuration issues CentOS on 5.1 cluster
I think enabling Admission Control was the solution. But I'm not sure. Looking back in the Events of vSphere client, early in the morning HA Protected was enabled. Thanks for your replies !!
View ArticleRe: How to recover VMFS volume after a RAID controller failure
Has the datastore initially been created with ESXi 5/VMFS5 (i.e. not an upgrade from ESXi 4/VMFS3)?What's the ouptut of:partedUtil getUsableSectors "/vmfs/devices/disks/mpx.vmhba1:C0:T1:L0" André
View ArticleRe: ESXi 4.0 Server Crashed
also run the commands listed on this pagehttps://communities.vmware.com/message/935007#935007
View ArticleRe: Regarding upgrade of license keys from Essentials plus 4.1 to Essentials...
Okay thank you for that information, then we will do the upgrade of the keys at the same time when we are upgrading the hosts and the vcenter server.
View ArticleRe: how do i use the UM across more than one vlan/network?
Please remember that Usage Meter does not talk directly to virtual machines. Usage Meter talks directly to vCenter itself, and the other VMware Products (e.g. vCOPs). One would hope that...
View ArticleRe: vmnic Status
Try something like this foreach ($dvSwinGet-VDSwitch){ foreach($esxin$dvSw.ExtensionData.Config.Host){ $esxObj=Get-View$esx.config.Host $nicTab=@{} $esxObj.Config.Network.Pnic|%{...
View ArticleClik here to view.
Can you use a domain account to create the DBA user for single sign-on?
Hi All, Is it possible to use a domain account credentials to use when installing single sign-on, it is asked during the database info page?See below; I've tried but entering domain credentials that I...
View ArticleRe: How to recover VMFS volume after a RAID controller failure
Hello,Thanks for your quick reply.Initially i have installed ESXi 5.0 and I am almost 100% sure that VMFS version was 5 (I have installed it more than 6 months ago and of course it wasn't...
View ArticleRe: ESXi 4.0 Server Crashed
You mentioned a 500GB drive in your initial post, but the output shows a 300GB drive!? Can you confirm it's the 300GB drive which should contain the VMFS datastore?Did you setup the host with ESXi 4.0...
View ArticleRe: ESXi 4.0 Server Crashed
Just saw your follow up post, where you mentioned you ran some commands. It's not a good idea to run commands without knowing the details, especially when you follow a 5 years old post. André
View ArticlevCenter with Windows 8 with Hyper-V (WP8 SDK) loses network after cloning
Hey! We have vSphere Server Version 5.1I have added the Windows 8 machine and managed to enable Hyper-V and installed Windows Phone 8 SDK.Now I see 3 network adapters: Ethernet, vEthernet and vEthernet...
View ArticleRe: vmnic Status
HI LucD, Thanks a lot for your reply. If a host is having both standard and distributed switch then how to find which one is standard and which one distributed.
View Articlecontinual NTCCheckResult messages in vmkernel log - issue
Hi all Dont suppose anyone knows why we'd be getting the following about every minute on a vsphere 5.1 U1 host (updated fully as of a few days ago). 2013-08-13T09:44:37.458Z cpu0:8802)TeamCheck:...
View Article